By Adams Heating & Cooling Team Published
Quick answer
In an older Michigan home, keeping the boiler usually makes sense when the radiators and piping are sound and the house heats evenly, since a boiler needs no ductwork. Switching to a forced-air furnace makes sense when you want central air and filtration, the boiler system is failing, or a remodel already opens walls for ducts. Many homeowners keep the boiler for heat and add cooling with a ductless mini-split.
Published · Reviewed
Part of our Boiler Heating guides.
What is the difference between a boiler and a furnace?
A boiler heats water (or makes steam) and circulates it through pipes to radiators, baseboard or in-floor tubing, while a furnace heats air and blows it through ductwork to registers in each room. Both commonly burn natural gas in Michigan, and both are rated by AFUE, the share of fuel that becomes usable heat over a season. The difference is what carries the heat: water and pipes, or air and ducts.
That difference shapes everything else. A boiler home usually has no ductwork, so there is no built-in path for central air conditioning, whole-house filtration or humidification. A furnace home has that path, which is why furnaces are paired with central AC so often.
Older Michigan boiler homes come in two main kinds. Hot-water (hydronic) systems pump heated water through radiators or baseboard and back to the boiler in a closed loop. Steam systems boil water and let the steam rise through the pipes to the radiators, where it condenses and drains back. The two need different equipment and different care, so the first thing a replacement estimate should confirm is which one your house has. Cast-iron radiators on either kind hold heat long after the boiler shuts off, which is a large part of why many owners of older homes like the way a boiler heats.
A boiler heats a home with hot water or steam through pipes and radiators, while a furnace heats it with warm air through ductwork.
How do a boiler and a furnace compare in an older home?
In an older home, a boiler keeps the existing radiators and plaster walls intact, while a furnace brings ductwork that also enables central cooling. The table sets out the main trade-offs.
| Factor | Boiler (hot water or steam) | Forced-air furnace |
|---|---|---|
| How heat reaches rooms | Radiators, baseboard or in-floor tubing | Ducts and registers |
| Feel of the heat | Even, radiant warmth with little air movement | Faster warm-up, moving air |
| Ductwork needed | None | Yes; must be added if the house has none |
| Central air conditioning | Not included; add ductless or a separate duct system | Shares the furnace's ducts and blower |
| Whole-house filtration and humidification | Not through the heating system | Can be added to the duct system |
| Disruption to switch to it | Low when replacing an existing boiler | High in a house without ducts: chases, soffits, wall and ceiling openings |
| Common upkeep | Bleeding air from radiators, checking water pressure | Changing filters, keeping registers clear |
Switching an older boiler home to a forced-air furnace usually means adding ductwork, which is the largest part of the conversion.
When does keeping the boiler make sense?
Keeping the boiler usually makes sense when the radiators and piping are in good shape, the house heats evenly and you value radiant comfort. Kalamazoo's climate leans heavily toward heating: the National Weather Service's 1991–2020 normals list 6,326 heating degree days and 710 cooling degree days, and Kalamazoo County is in IECC climate zone 5A. A heating system that already keeps the house comfortable through that many cold days is worth a careful look before it is torn out.
The main thing a boiler home gives up is central cooling. For many households the answer is to keep the boiler for heat and add cooling separately, often with a ductless mini-split that needs only a small line set through the wall. See Ductless Mini-Split vs. Central AC: Which Fits Your Michigan Home? for that comparison.
A boiler that already heats a house evenly can be kept for heat while cooling is added separately with a ductless system.
When does switching to forced air make sense?
Switching to forced air makes most sense when you want whole-house central cooling and filtration, the boiler or its piping is failing, or a major remodel will already open walls and ceilings. A remodel that exposes framing is the least disruptive moment to run new ducts.
A switch can also change your options for the future. With ductwork in place, you can choose a gas furnace, a heat pump or a dual-fuel system later; our comparison of heat pumps, gas furnaces and dual fuel explains those choices. Gas furnaces must currently meet 80% AFUE; a 95% AFUE minimum is scheduled for furnaces made from December 18, 2028, and that rule is under litigation and a pending delay petition.
The least disruptive time to convert a boiler home to forced air is during a remodel that already opens walls and ceilings for new ductwork.
What goes wrong in a boiler-to-furnace decision?
The common mistakes come from underestimating the house rather than the equipment.
- Underestimating ductwork. Older homes with plaster walls and few open chases can force ducts into closets, soffits or lower ceilings, and undersized ducts make a new system noisy and uneven.
- Replacing a boiler without checking the radiators and piping. Air in the system, sludge or failing valves can make a new boiler perform like the old one. Our post on how to bleed a boiler radiator covers one routine fix.
- Copying the old boiler's size. Many older homes have been insulated or had windows replaced since the original boiler went in; a load calculation should set the size.
- Leaving a water heater alone in the chimney. If a new high-efficiency boiler or furnace vents through plastic pipe, a gas water heater may be left venting by itself into a flue sized for two appliances, which may then need a liner.
Either way, the work typically needs a mechanical permit from your local building department. The City of Portage, for example, requires one to replace a mechanical system, and the City of Kalamazoo lists boilers as mechanical-permit work.
A replacement boiler or furnace should be sized from a load calculation, because insulation and window upgrades often reduce an older home's heating load.
How do you decide for your home?
You decide by pricing both paths for the same house: a boiler replacement that keeps your radiators, with cooling added separately if you want it, and a full forced-air conversion including ductwork. Seeing both on paper, with the disruption to walls and ceilings described, usually makes the answer clear.
Adams Heating & Cooling is a family-owned company that has served Kalamazoo for 30+ years and works on both boiler heating and furnace installation and replacement. Estimates on replacements and new installation are free (see Current Specials), HVAC Financing through Optimus Financing is available, and our Google reviews show what homeowners say. To talk about your house, request service or call (269) 349-7240 (24-hour emergency service).
A fair boiler-versus-furnace comparison prices both paths for the same house, including ductwork and any separate cooling.
Frequently asked questions
Is a boiler better than a furnace?
Neither is better in every home. A boiler gives even, radiant heat with no ductwork, while a furnace heats faster and shares ducts with central air conditioning and whole-house filtration. In an older home with good radiators, keeping the boiler is often simpler; in a home that needs central cooling, a furnace may fit better.
Can I add central air to a house with a boiler?
Yes, but it needs ductwork and an air handler, which in older homes can mean significant work in closets, soffits and ceilings. A ductless mini-split is a common alternative because it needs only a small line set through the wall to each indoor unit.
How hard is it to convert from a boiler to forced air?
The hard part is the ductwork, not the furnace. Homes with plaster walls and few open chases may need ducts routed through closets or soffits. A remodel that already opens walls and ceilings is the least disruptive time to convert.
Should I replace my boiler with the same size?
Not automatically. Many older homes have been insulated or had windows replaced since the original boiler was installed, so a load calculation should set the size of the replacement.
Do I need a permit to replace a boiler or furnace in Michigan?
In most cases, yes. Replacing a boiler or furnace typically needs a mechanical permit from your local building department; the City of Kalamazoo, for example, lists boilers as mechanical-permit work. Our guide to HVAC and Water Heater Permits in Kalamazoo County lists the confirmed issuing offices.
Why do my radiators have cold spots?
Trapped air is a common cause, and bleeding the radiator often fixes it. If cold spots keep returning after bleeding, the system's water pressure, valves or piping may need a technician's attention.
Sources
- National Weather Service Grand Rapids — Kalamazoo Annual Climate Report (accessed November 19, 2026)
- Pacific Northwest National Laboratory — Guide to Determining Climate Zone by County (PNNL-33270) (accessed November 19, 2026)
- City of Portage — Mechanical Information Sheet (accessed November 19, 2026)
- City of Kalamazoo — Apply for a Mechanical Permit (accessed November 19, 2026)
- Federal Register (govinfo) — Energy Conservation Standards for Consumer Furnaces, Final Rule (88 FR 87502) (accessed November 19, 2026)
- ACCA — U.S. Supreme Court Reopens Non-Condensing Furnace Fight (accessed November 19, 2026)
- Federal Register (govinfo) — DOE Request for Comment on the Consumer Furnace Rule Delay Petition (accessed November 19, 2026)
